Fastening bolts at valve on gas tower was cracked after used 6 months.
储气塔运行半年即发生了阀门紧固螺栓的断裂事故。
This article makes clear analyses on the damage occurred frequently on the fastening bolt.
文章从隔爆外壳紧固螺栓容易损坏的两个方面进行了分析 ,并就紧固螺栓的设计从螺栓强度、铸铝外壳螺纹牙强度、螺栓的预紧力矩的计算、螺栓的防松及精度等方面进行了设计举例 ,供从事防爆电气行业的有关人员参考和借
The fastening bolts of steam turbine cylinder case were in fatigue-creep interaction.
调峰机组频繁调整负荷,汽轮机汽缸紧固螺栓处于疲劳-蠕变交互作用,对紧固螺栓多轴应力下疲劳-蠕变损伤的研究对调峰机组安全运行和维修具有重要意义。
Lock rings at the end of shaft with bolt
GB/T892-1986螺栓紧固轴端挡圈
Study on Localization Technology of Bolt Fasteners for CPR1000 Internals
CPR1000堆内构件螺栓紧固件的转化设计
" Tolerances for fasteners--Bolts, screws and nuts"
GB/T3103.1-1982紧固件公差螺栓、螺钉和螺母
Fasteners--Clearance holes for bolts and screws
GB/T5277-1985紧固件螺栓和螺钉通孔
" Mechanical properties of fasteners--Bolts, screws and studs"
GB/T3098.1-1982紧固件机械性能螺栓、螺钉和螺柱
Replace the body bolts and tighten evenly.
重新放置阀体螺栓，并均匀紧固。
Tighten exhaust manifold to cylinder head bolts.
紧固排气岐管汽缸头螺栓。
Experimental Study on Fastening Bolt Axial Force of WSGG Anchor Basted on CFRP Sheet
CFRP波形齿锚具紧固螺栓轴力的试验
Fasteners--Counterbores for hexagon bolts and nuts
GB/T152.4-1988紧固件六角头螺栓和六角螺母用沉孔
" Fasteners--General requirements for blots,screws,studs and nuts"
GB/T16938-1997紧固件螺栓、螺钉、螺柱和螺母通用技术条件
" Fasteners--Bolts,screws,studs and nuts--Symbols and designations of dimensions"
GB/T5276-1985紧固件螺栓、螺钉、螺柱及螺母尺寸代号和标注
" Mechanical properties of fasteners--Stainless steel bolts,screws, studs and nuts"
"GB/T3098.6-1986紧固件机械性能不锈钢螺栓,螺钉,螺柱和螺母"
" Mechanical properties of fasteners--Bolts, screws, studs and nuts made of non-ferrous metals"
GB/T3098.10-1993紧固件机械性能有色金属制造的螺栓、螺钉、螺柱和螺母
" Surface discontinuities of fasteners on bolts, screws and studs for general requirements"
GB/T5779.1-1986紧固件表面缺陷--螺栓、螺钉和螺柱--一般要求
Surface discontinuities of fasteners on bolts screws and studs-Special requirements
GB/T5779.3-1986紧固件表面缺陷--螺栓、螺钉和螺柱--特殊要求
" Tolerances for fasteners--Bolts, screws and nuts for fine mechanics"
GB/T3103.2-1982紧固件公差用于精密机械的螺栓、螺钉和螺母
Tighten all bolts evenly as for a standard flange assembly.
均匀地紧固所有螺栓，形成标准的法兰总成。
After seven days, the grouted mortar will have concreted, then we shall tighten the anchor bolts.
灌浆在七天以后凝固，我们就将拧紧地脚螺栓。
