The other is the strength of weld lines takes from for fiber orientation distribution parallel to weld lines.
这种取向的产生一方面会导致制件不同方向的收缩,另一方面在熔接线区的纤维取向方向因平行于熔接方向而大大降低其熔接线强度,制件整体强度下降。
Based on results of moldflow simulatio n, default diagnosis of weld lines is developed and solution is given.
基于moldflow的模拟分析结果,对熔接线缺陷进行了诊断,并给出了解决方案。
Study on Influence of Processing Parameters on Weld Line Tensile Performance of Injection Molded Nylon 6/Montmorillonite Nanocomposites;
注塑工艺参数对尼龙6/蒙脱土纳米复合材料熔接线拉伸性能影响的研究
In this study,molding condition including melt temperature,mold temperature,packing pressure and injection speed on the mechanical properties particularly the weld line strength of injection molded nylon 6 nanocomposites were investigated.
针对纳米尼龙6,研究了熔体温度、模具温度、保压压力和注射速度等工艺因素对具有熔接线和无熔接线注塑件拉伸强度的影响。
The tensile strength of injection-molded glass fiber-reinforced PA66 (Zytel 70G33L) with weld lines, with different obstacle size in cavity and at the same processing conditions, are studied by both numerical simulation and physical test.
通过对相同工艺条件下PA66(Zytel 70G3 3L)熔体绕过不同障碍物数值和实验研究 ,发现决定熔接线强度的主要因素是两股熔体相遇时的熔接角 ,熔接线强度会随着熔接角的增大而加强。
Flow induced birefringence of weldline region in polystyrene injection molding;
注射成型熔接线区域流动诱导双折射行为
The Level Set/Ghost method was introduced to dynamically simulate the weldlines in the symmetric thin mold with rectangle cylinder precisely.
为了准确模拟具有对称结构的带有矩形嵌件的薄壁型腔内熔接线的动态形成过程,采用Level Set/Ghost方法追踪充填阶段聚合物熔体前沿界面。
Combined with the design of injection molds and actual production,technical gists ofinjection molding design are introduced on the number of gates,flow pattern,gate position,weldline position and runner design.
结合注塑模设计和生产的实际,重点介绍了注塑模模流设计在浇口数目、流动形态、浇口定位、熔接线位置、浇道设计等方面的技术要领。
Applying sequential injection moulding to control weld-line locations;
顺序浇注成型控制熔接线位置研究
Analysis of flexural strength of RC members strengthened with high strength steel wire mesh and polymer mortar;
高强钢绞线网—聚合物砂浆抗弯加固的承载力计算
They also look for potential molding defects, such as gas entrapment, weld lines, shorts and sinks.
也可以看出潜在的模塑缺陷如气体夹陷、熔接线、缺胶和凹陷等。
Repair connector terminal or wire splice.
维修接头端子或电线熔接处。
Performance of External Fuse Protection and Connection Mode of Capacitor Group
外熔丝保护性能与电容器组接线方式
Methods for radiographic inspection and classification of radiographs for fusion welded butt joints in steel
GB/T3323-1987钢熔化焊对接接头射线照相和质量分级
Broken connector terminal or wire splice in fog lamp circuit.
雾灯电路的接头端子或电线熔接处断裂。
Damage Behavior of Welded Joints with Defects on Fusion Line;
熔合线含缺陷焊接接头损伤行为的研究
Analysis about a Case of Grounded Spot Fusing of Optical Fiber Composite Overhead Ground Wire
一起光纤复合地线搭接地点熔断案例的分析
Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.
连接条和接线柱的焊接必须使极柱顶部和盖子的铅衬套与连接条环口或接线柱完全熔焊牢固。
Methods of radiographic inspection and quality classification of circumferential fusion welded butt joints in steel pipes and tubes
GB/T12605-1990钢管环缝熔化焊对接接头射线透照工艺和质量分级
Study on Fracture Performance and Engineering Safety Evaluation Method of Welded Joints Containing Crack on Fusion Line;
熔合线含裂纹焊接接头断裂性能及其工程安全评定方法研究
REMOVE AND INSPECT FUSE #7
移走并检查＃熔线。
REMOVE AND INSPECT FUSE #:
拆掉并检查熔线＃。
TO PDC "ABS PUMP" FUSE
ＰＤＣ＂ＡＢＳ油泵＂熔线
PUMP/MOTOR FUSE (ABS PUMP)
泵／马达熔线（ＡＢＳ泵）
REPAIR THE OPEN IGN SWITCH OUTPUT WIRE FROM THE IGN SWITCH TO THE JUNCTION BLOCK.
从熔断点火开关到连接块维修断开的点火开关输出线。
Synchronous On-line Detect of Welding Process Parameters and Molten Droplet Images in GMAW-P;
脉冲GMAW焊接电参数波形及熔滴过渡图像的同步在线检测
contact heat thermosol unit
接触式热熔染色装置
fuse or cause to grow together.
熔合或接合在了一起。
