Aim at the problem that the broken hole usually appears in demoulding, the process and key technology of demoulding based on Pro/E are described.
以Pro/E为平台 ,针对模具拆模过程中经常出现破孔的问题 ,论述了注射模具拆模的基本原理、流程、分模面的设计 ,以及分模面设计中填补破孔的三种主要方法 ,包括定义“环闭合”、定义“填充环”和构建曲面片 ,并介绍了各种方法的优缺
The paper discusses the keypoints in supervision activities including mould erection and demoulding of precast hollow bridge plate,steel bar,prestress steel strand and concrete in prestress reinforced concrete construction for purpose of improving supervision work quality.
论述了预应力钢筋混凝土预制空心桥板支模、拆模和钢筋、预应力钢绞线等监理工作要点,以利于提高监理工作质量。
Simple early form-removal system of floor slab structure is put forward considering the defects of traditional formwork.
结合楼板结构常规模板存在的缺陷,提出了简易早拆模板体系。
With a brief introduction to the basic idea of constructivism theory,this paper focus on its application process in the training course of mould dismantling and drawing.
简要介绍了建构主义学习理论的基本观点,重点介绍了在模具拆装测绘实训课程中应用建构主义学习理论的具体过程及应用建构主义学习理论的几点体会。
Research on characteristics about complex shearing wall system with moulding board;
免拆墙模复合剪力墙体系的特性
The Study of Early-dismantling Template System and Dismantling Template Time of Concrete Structure;
混凝土结构早拆模板体系与拆模时间的研究
Research of Optimal Mold Parting Methods Based on Pro/Engineer
基于Pro/E模具最优拆模方法的研究
Concrete curing should immediately start after frame removed.
6砼拆模后立即均匀涂刷砼养护液。
THE TECHNOLOGY OF ASSEMBLED FIELD-CAST CONCRETE WALL WITHOUT DEMOULDING
拼装式现浇混凝土墙体免拆模板技术
Experimental Study on Non-Dismantling Template of the Concrete Contains Glass Fiber
玻璃纤维混凝土免拆模板的实验研究
Door Module Remove/Install
车门模组拆卸/安装
KEY OFDISCONNECT TRANSMISSION CONTROL MODULE.
关闭。拆开变速控制模组。＊＊
Remove the door module from the trim panel.
从饰板上拆卸车门模组。
Research on disassembly model and disassembly sequence planning based on modularization
基于模块化的拆卸模型及拆卸序列规划研究
Drop-forged rivetless chains for conveyors
GB/T17482-1998输送用模锻易拆链
Scot has a do-it-yourself model airplane kit.
斯科特有一套可拆装的模型飞机组件。
DISCONNECT THE SEAT BELT CONTROL MODULE.
拆卸座位安全带控制模组。＊＊
Airbag Control Module Connector Removal
安全气囊控制模组接头拆除
Push Button Module Remove/Install
按压按钮模组的拆卸/安装
Product information model for disassembly and recycling is developed.
建立面向拆卸回收的产品信息模型。
DISCONNECT & REMOVE THE BODY CONTROL MODULE FROM THE JUNCTION BLOCK.
从集成板上拆下并移走主体控制模组。＊
A Method of Disassembling Assur-Groups for Identifying and Modelling by Computer
适于计算机辨识建模的杆组拆分方法
Study of Chiral Separation of Tryptophan Enantiomers and Process Simulation;
色氨酸对映体的手性拆分及过程模拟
