The geometrical parameter design and calculation of screw axis for bagasse feed-in were systematically introduced which provided the theoretical basis for solving the problems of bagasse feed-in of the defibrato in the early stage.
较系统的论述了适于蔗渣进料用的螺旋轴几何参数的设计与计算,为解决早期制造的热磨机出现难进料及效率低的问题提供理论依据。
With allowing deflection curvature as stiff-ness condition and adjusting firmness as main calculatingmethod, the paper discusses seriation and fatigue life sforecast of screw axis s shaft diameter and span in screwconveyer with bending.
提出以许用挠曲率为刚度条件,以校核刚度为主要计算方法,对受弯扭作用的螺旋输送机螺旋轴进行轴径和跨度的系列化设计;研究了根据挠曲率进行疲劳寿命预测,列出尺寸表供设计时选用;研究了螺旋轴折断的原因。
The geometrical parameter design and calculation of screw axis for straw feed-in that provided the theoretical basis for solving the problems of straw feed-in of the defibrator in the early stage were systematically introduced.
较系统地论述适于麦秆进料用的螺旋轴几何参数的设计与计算,为解决早期制造的热磨机出现进料难及效率低的问题提供理论依据。
conveyer screw shaft coupling
输送机螺旋轴联轴节
Design Method and Fabrication Technology of the Shaft of Screw Press
螺旋挤浆机螺旋轴结构优化设计与加工工艺
The calculation and balance of the axial force of borehole helico-axial multi-phase pump
井下螺旋轴流式多相混抽泵轴向力计算及平衡
Deformation analysis on cantilever screw conveyer shaft based on method of dynamic double barycenters
基于动态双重心法的悬臂螺旋输送机螺旋轴的变形分析
measurement of fit clearance of propeller
螺旋桨轴安装间隙测量
helix-to-coaxial-line transducer
螺旋同轴线匹配变换器
spiral bevel gears with offset axes
轴线偏置螺旋伞齿轮
bonding of propeller to shaft
螺旋桨与轴胶合联结
Inspection machining dimension of propeller shaft( intermediate shaft or counter shaft).
螺旋桨轴（间轴）加工尺寸检查。
Aligning intermediate shaft and propeller shaft after launching.
下水后中间轴和螺旋桨连接后校中。
contrarotating propeller
同心套轴的两个对转螺旋桨
contra turning propeller
同心套轴的两上对转螺旋桨
split outer race of the wound roller bearing
螺旋滚柱轴承拼合外座圈
Study on Creep Characteristic of Propeller Shaft in Especial Condition;
特定环境下螺旋桨尾轴蠕变特性研究
Research of 5-Axis Machining Technology for Large-scale Marine Propeller;
大型舰船用螺旋桨五轴加工技术研究
Analyses on the Reliability of the Strength Design for the Propeller Shaft;
船舶螺旋桨轴强度设计的可靠性分析
Discussion on Machining of Propeller Shaft for 230 000 DWT Ore Carrier
230000DWT矿砂船螺旋桨轴加工问题探讨
Optimum Figuration of Helix S-Type Vertical Axis Wind Tubine
螺旋形S型垂直轴风轮结构优化设计
