Dynamic modelling of hot-spot temperature in oil-immersed power transformers;
油浸式大型变压器热点温度的动态模型
The hot-spot temperature was reduced due to a lot of arch drips appear in glass .
由于玻璃板中出现大量的碹滴,我们采取了降低热点温度的方法使碹滴问题得到了解决,但同于热点温度的降低,玻璃的微观质量比降温前下降了很多;针对这一点我们通过调整下班组成和配合料质量,达到改善和提高玻璃质量的目的。
Method of loop up load table and hot-spot temperature calculation are applied to assess the overload capacity of large oil-immersed power transformer under the conditions of normal periodic overload and accident overload,and countermeasure against risk of accident ov.
并应用查负载表法和热点温度计算法评估大型油浸式电力变压器正常周期性过负荷和事故过负荷能力,给出了500 kV大型油浸式电力变压器事故过负荷运行风险的应对措施。
Last,the correlation coefficient revised in regression analysis are adopted to select the temperature measurement points.
先采用模糊聚类对温度变量进行分组,然后根据温度变量与热变形的相关性在每组中选择典型的温度变量,最后根据回归分析中经过修正的相关系数选择测温点。
The inordinate temperature rise in oil-immersed transformers is featured by hot spot temperature(HST).
变压器在温升过程中温度分布不均,热点温度是其中具有代表性的确定变压器最优化负载的重要参数。
Study on measuring of heavy oil inflection point temperature;
稠油拐点温度测算方法研究
According to the results of the experiments,the formation ignition temperature of Zheng-408 was precisely confirmed at 365 ℃ to 375 ℃.
结果表明,郑408块油藏点火温度为365~375℃,火烧前缘推进速度与注气强度呈正相关,在充分注气燃烧条件下,地层不会出现结焦现象;火烧之后岩石矿物组分改变有利于储层渗透性能的改善,但变化不大。
The influences of various ignition temperatures and environmental temperatures on the synthesis were examined.
考察了不同点火温度以及不同环境温度的影响 ,并与硝酸盐直接煅烧分解进行了比较 。
The design idea of optimization control of ignition temperature system for LAIGANG 265m2 sintering machine and its composition were presented in this paper.
介绍了莱钢烧结厂265m烧结机点火温度优化控制系统的控制思想及控制系统的构成。
Improved Method for Calculation of Hot-spot Temperature in Power Transformer
改进的变压器绕组热点温度估算方法
Thermal Model for Hot Spot Temperature Calculation in Oil-immersed Transformers
油浸式变压器绕组热点温度计算的热路模型
The FBG Monitoring Principle of Transformer Internal Temperature and the Improved Method for Calculation of the Hot-Spot Temperature
变压器内部温度光纤传感监测及绕组热点温度计算改进方法
Calculation model of HV power capacitor internal hottest-spot temperature
高压电力电容器内部最热点温度的计算模型
This paper presents a new-type instrument for on-line monitoring the coiling hot-point temperature of an oil-immersed transformer.
本文介绍了一种新型油浸式电力变压器绕组热点温度在线监测仪。
hot junction temperature
热接点温度（热电偶）
The dots turn red as they register heat.
温度点变红以标记热度．
After reading the thermometer, he said, " You have a slight fever."
他看了看体温表说：＂你有一点热度。＂
Detection of Heating Endpoint Temperature for Fish by SDS-PAGE Method
SDS-PAGE电泳法检测鱼肉热处理终点温度
The melting sticking occurred when the melting point of materials is lower than the drying temperature.
物料熔点低于干燥温度时容易产生热熔性粘壁。
Selecting the Temperature Measurement Points of the NC Machine Tool and Constructing the Compensated Model of the Thermal Error;
数控机床温度测点选取及热误差补偿建模
Research on Air Preheater Hot Spots Detection System Based on Image of Temperature Field;
基于温度场分布图的空预器热点检测系统研究
Effect of the Positions of Thermocouples on the Wall Temperature Measurement;
测点分布对多孔管道加热面温度测量的影响
The Development of a Thermal Deformation and Vicat Softening Temperature Microcomputer Measurement and Control System;
热变形与维卡软化点温度微机测控系统的研制
The Design and Implementation of Heat Treatment Furnace Multi-point Temperature Control System
热处理电炉多点温度控制系统的设计与实现
Study on acid dew point temperature change follow heat pipe tube bank combination
热管管排组合对露点腐蚀温度影响研究
Temperature Field Simulation and Thermal-Stress Analysis of Al Alloy Pressure diecasting Die
铝合金压铸模具温度场模拟与节点热应力分析
auto-ignition temperature
自燃温度自动点火温度
