The maximum temperature and supreme pressure in the accident are calculated on the hypothesis that the combustible substance is TNT and it burns in an adiabatic and .
某化工厂TNT碱性废水沉淀池在清理过程中发生了火灾事故,在现场调查的过程中,从附着在沉淀池上的可燃物成分入手,详细分析了造成此次火灾事故的主要原因,并在假定附着在池壁及立柱上的红棕色物质为纯TNT和事故中TNT为等容、绝热燃烧的前提下,计算出了事故中TNT燃烧的最高温度及最大压力。
For the terrestrial ecosystem, the daily maximum temperature is the important factor determining the normal photosynthetic mechanism control,fruit quality and glaciers melting.
自20世纪50年代以来,中国北方最高和最低温度变化的特点是:最低温度升温速率大于最高温度的升温速率;冬季升温速率大于夏季;偏北(纬度较高)地区的升温速率大于偏南(纬度较低)地区。
Based on the daily maximum temperature of mid-summer(June to August)from 1950 to 2005,T213 grid wind data,and vertical velocity from June to August in the year of 2002 and 2003 in Wuhan,the climatic characteristics of mid-summer high temperature,high temperature processes and characteristics of the western Pacific subtropical high activities are studied.
利用1950～2005年盛夏(7～8月)逐日武汉市最高温度、2002年和2003年6～8月T213格点风和垂直速度资料,分析了武汉盛夏高温的气候特征,研究了高温过程及西太平洋副热带高压活动特点。
The relation between the maximum temperature and the switching condition of an LDMOST under different frequencies is studied.
研究了LDMOS器件内部的最高温度与开关频率之间的关系。
The Monte Carlo simulation technique was employed to investigate the kinetics of propylene polymerization in order to determine the validity of the stationary state assumption and the effects of the polymerization temperature on the polymerization.
同时,模拟得到了聚合温度对丙烯聚合过程的转化率、分子量的影响。
The factors that affect the quality of the polycaprolactam are studied,including the polymerization temperature,the liquid surface control of the polymerization tube,oxygen,additives,ring opening agent,molecular stabilizer and the purity of polycaprolactam The process requirement must be meet to produce high-quality products.
聚己内酰胺的生产过程复杂且影响因素很多;研究了生产工艺中聚合温度、聚合管液位的控制、氧等影响因素,外加剂开环剂、分子量稳定剂以及原材料己内酰胺的纯度对聚己内酰胺质量的影响;为得到高质量的产品,必须严格按工艺要求操作。
High quality PVC resins with polymerization degree of 800 and less "fish eyes" were produced through optimizing the composition,such as reducing the polymerization temperature,adjusting the ratio of composite initiators and the using amount of chain transfer agents,adding anti-"fish eye" agents,and so on.
通过降低聚合温度,调整复合引发剂配比、链转移剂用量,加入抗"鱼眼"剂等方法进一步优化了工艺配方,制备出"鱼眼"数少、树脂质量好的聚合度为800的PVC树脂。
The average temperature falls between the highest and lowest points of heat and cold.
平均温度是指最高温度和最低温度之间的温度。
the maximum temperature, voltage, volume
最高温度、 最高电压、 最大体积
mean daily maximum temperature
逐日最高温度平均值
records the highest and lowest temperatures reached during a period of time.
记录在一定时期的最高温度和最低温度的温度计。
Yesterday s high was ninety eight degrees.
昨天的最高温度是九十八度。
The weatherman says the highest temperature for tomorrow will be 10 degrees centigrade .
天气预报说明天最高温度是摄氏度10度。
Fibers are usually heat- set at a temperature at least 30 c higher than the highest temperature expected in use.
纤维的定形温度通常至少要高于使用时的最高温度30℃。
The highest permissible temperature in the cavity for charging is ＋50℃.
装药时药室中允许的最高温度为正50度。
For the design of hydraulic pressure. extreme temperature that may occur in use should be considered as design since the hydraulic preddure have a certain relation with temperature.
由于耐水压与温度有关，所以在设计时应考虑可能达到的最高温度。
a maximum [minimum] thermometer
最高 [最低] 温度计
maximum assessed fuel element temperature
燃料元件最高设定温度
Hardness was decreased after maximum by high temperature heating.
高温加热硬度达最大硬度以后保温硬度降低。
The highest temperature is about 38 c.
最高温大约是摄氏度38度
The highest temperature is about 38℃ .
最高温大约是摄氏度38度。
Oh, that's pretty high.What is the highest temperature you get here?
够高的！这儿气温最高能达到多少度？
The dew point is the highest temperature to which the air cools to saturation moisture content.
露点是空气降温到含水量饱和的(最高)温度。
The high temperature for today was 78 degrees.
“今天最高气温达到了78华氏度，
Massive stars are hottest in their central regions.
大质量恒星的中心区域温度最高。
