Resistance of mold plates to heat transfer and heat transfer coefficient between cooling channel walls and water were taken into account for obtaining a suitable mold temperature.
以达到注塑件模具的某一模温为优化目标 ,考虑了模板热传导阻力和水对冷却水道壁的给热系数 ,用试差法求解冷却水道一边所需的传热面积 ,并完成冷却系统的设计计算。
Study on the frictional behavior of zinc-coated sheet in warm die;
温模条件下镀锌钢板摩擦行为研究
The investigation results indict that in micro injection molding the mold temperature is the important factor influencing on the melt flowing in microsca.
结果表明,微注塑成形中,模具温度是影响微尺度下熔体流动的重要工艺因素,且随通道截面尺寸的减小而逐渐增大;而壁面滑移对微小熔体流动行为的影响,也随通道尺寸的减小而增大。
The influence of injection pressure?pouring temperature and mold temperature on the microstructure, casting character and properties of ZA85 magnesium alloy has been carried out, the best die casting process was obtained under cold chamber, also analyse its cast structure simply, and small batches of magnesium alloy automobile parts are produced successfully.
研究了压射比压、浇注温度、模具温度三个压铸工艺参数对ZA85镁合金显微组织、铸造性能和力学性能的影响,探明了其在冷室压铸条件下的最佳工艺,简单分析了压铸态组织,并成功的实现了镁合金汽车零件的试制。
The paper presents some of the results obtained from an investigation on the influence of injection pressure,pouring temperature,mold temperature and shot speed on the microstructure,castability and mechanical properties of AM60B magnesium alloy under the condition of cold chamber.
研究了压射比压、浇注温度、模具温度、压射速度四个压铸参数对AM60B镁合金显微组织、铸造性能和力学性能的影响,探明了其在冷室压铸条件下的最佳工艺,简单分析了压铸态组织,并成功地实现了镁合金灯罩铸件的试制。
Water temperature model and simulation of surface water source heat pumps
地表水地源热泵水温模型与水温模拟分析
Study on the 2-D Water Temperature Vertical Model Simulation for the Stratified Reservoir
分层水库垂向二维水温模型模拟研究
Observation on complications of ice blanket hypothermia apparatus under different modes
冰毯降温仪不同降温模式下的并发症观察
Temperature Control Model and Its computer System for the Forging Gas heating furnace
锻造煤气加热炉自动控温系统及控温模式
Beyond Wenzhou Culture, Spirit and Mode;
温州文化、温州精神与温州模式的超越
An Explorative Analysis on Transition from "Wenzhou Model" to "Wenzhounese Model;
由“温州模式”到“温州人模式”探析
Research on High Temperature Fatigue Life Models of Powder Metallurgy;
粉末高温合金高温疲劳寿命模型研究
The Electromechanical Fuzzy Control Research of the Temperature in a Solar Greenhouse;
太阳能温室温度的机电模糊控制研究
Design of Fuzzy Self-turning PID Control Greenhouse Temperature Controller
模糊自整定PID温室温度控制器的设计
Simulation on Temperature Field of TB6 Titanium Alloy Ingots in Heating Process
TB6钛合金升降温过程温度场的模拟
Numerical Simulation on Soil Temperature Field and Heat Drop in Hot Crude Pipeline
热油管道温降及土壤温度场数值模拟
Modeling and Simulation on Temperature Dynamic Model in Greenhouse during Summer
温室系统夏季温度动态模型的建模与仿真
Simulation of Development and Growth of Greenhouse Muskmelon;
温室网纹甜瓜生长发育模拟模型研究
A Comparative Study of "New Suzhou Pattern" and "Wenzhou Pattern" of Development;
“新苏州模式”和“温州模式”比较研究
Comparative Studies and Apocalypse on "Wenzhou Mode" and "Sunan Mode;
“温州模式”和“苏南模式”比较研究及启示
Study on Greenhouse Fruit Cucumber Growth and Development Simulation Model
温室水果黄瓜生长发育模拟模型研究
Numerical Simulation of Temperature Field and Stress Field of Glass Mould
玻璃模具的温度场和应力场数值模拟
Simulation Model on the Accumulation of Sucrose,Citrate with Temperature Accumulative of Melon Fruit under Protected Cultivation
温室甜瓜果实糖酸积累模拟模型研究
