The process improvement of seat- joined flange is introduced, and its punching process procedure and the key points in die design under the condition of lots manufacture are briefly analyzed.
介绍了接座法兰的工艺改进,简要分析了批量生产条件下其冲压工艺过程及模具设计要点,并阐述了机加工件改冲压件的优点、可行性、经济性等。
LY12 Flange in Squeezing Casting;
LY12法兰盘整体加压挤压铸造工艺试验
Research and Application of Wave-guide with the Flange Electroforming Connection Technology;
波导管与法兰盘电铸连接工艺的研究与应用
Squeeze Casting Technology and Mould Design on Flange Prepared by 6082 Aluminum Alloys
6082合金法兰盘挤压铸造工艺及模具设计
Flanges for waveguides-Part 7: Relevant specification for flanges for square waveguides
GB/T11449.6-1989波导法兰盘第七部分:方形波导法兰盘规范
Flanges for waveguides-Part 4: Relevant specification for flanges for circular waveguides
GB/T11449.4-1989波导法兰盘第四部分:圆形波导法兰盘规范
Flanges for waveguides-Part 2: Relevant specification for flanges for ordinary rectangular waveguides
GB/T11449.2-1989波导法兰盘第二部分:普通矩形波导法兰盘规范
Flanges for waveguides-Part 6: Relevant specification for flanges for medium flat rectangular waveguides
GB/T11449.5-1989波导法兰盘第六部分:中等扁矩形波导法兰盘规范
Flanges for waveguides-Part 3: Relevant specifications for flanges for flat rectangular waveguides
GB/T11449.3-1989波导法兰盘第三部分:扁矩形波导法兰盘规范
Flanges for waveguides-Part 1: General requirements
GB/T11449.1-1989波导法兰盘第一部分:一般要求
telltale flange
接放空管或取样管的法兰盘
Liquid Die Forging Technology for 5083 Aluminium Alloy Flange
5083铝合金法兰盘液态模锻成形技术
Optimization Design of Forging-die for Automobile Flange Based on Response Surface Method
基于响应面方法的汽车法兰盘锻模优化设计
On Substitution of the Butt Welding between 35-steel for the Butt Welding of 16Mn and 35-Steel in the Connection of Drilling Pipe and Flange;
35钢代替16Mn用于钻杆管与法兰盘的对焊
Squeeze Casting Technology and Mould Design on Flange Prepared by 6082 Aluminum Alloys
6082合金法兰盘挤压铸造工艺及模具设计
Cracking Reason Analysis of Domestic A105 Flange Used in Gas Pipeline
输气管线用国产A105钢法兰盘的开裂原因分析
ceramic flange for tubes, non-refractory (excl. for laboratory or electrical)
管用陶瓷法兰盘,非耐火（不包括实验室或电气用者）
Turn the locking bolt so that it is fixed on the bake cover or the flange plate.
安装后必须将锁紧螺母锁紧在电机后端盖或法兰盘上。
Turn the hollow bolt so that it is fixed on the bake cover or the flange plate.
安装后必须旋出空心螺栓锁紧在电机后端盖或法兰盘上。
The engine-feed system interface is at the turbopump inlet flanges.
发动机与供应系统的交界是在涡轮泵的进口法兰盘处。
The methods for calculation of additional vertical bending moment and confining bending moment of flanges are deducted, and the type and quantity of radial reinforcements are proposed.
为此，导出了竖向附加弯矩和法兰盘约束弯矩的计算方法，提出了径向联系筋的形式及数量。
Modular units for machine tool construction--Tenon drive and flanges for mounting multi-spindle heads--Dimensions
GB/T3668.13-1983组合机床通用部件安装多轴箱用的法兰盘和端面传动键尺寸
