Formation of freshwater lens in islands and evolution rules of the upconing
海岛淡水透镜体形成及倒锥演变规律分析
Using self-study model to simulate freshwater lens evolution at laboratory,it s formation process in the condition of rainfall has been simulated,the process of upconing movement has also been simulated without any recharge.
模拟了降雨补给条件下淡水透镜体的形成过程;在无补给条件下,开采淡水时倒锥的变化过程。
Relying on its excellent strength and stiffness,circular-shaped cover with a topsy-turvy cone is especially suitable for the end sealing of detachable spiral heat exchanger.
倒锥平盖凭借其良好的强度、刚度特性,尤其适于可拆式螺旋板换热器的端部密封。
The results show that the main reasons are small back draught of the crystallizer,large level fluctuation,high degree of superheat of the tundish and the poor quality of the cooling water for the crystallizer.
由于方坯角部纵裂漏钢事故频繁,通过分析漏钢的特点和机理,认为造成小方坯角部纵裂漏钢的主要原因是结晶器倒锥度小、结晶器液面波动及中间包过热度大、结晶器冷却水质差。
In order to improve the using life of the mould, through constantly exploring in the production practice, the optimal back draught is determined, the mould structures such as water canal distributing, the water ring nozzles and so on are reconstructed, adopting low degree of superheat in pouring and using appropriate protecting slag, and then the mould life is increased from 316 to 774 heats.
为了提高结晶器的使用寿命 ,通过生产实践中的不断探索 ,确定了最佳的倒锥度 ,并对水缝分布、水环喷嘴等结晶器结构进行改造 ,采用低过热度浇铸 ,使用合适的保护渣 ,结晶器使用寿命由原来的年平均 3 16炉提高到 774炉。
Machining Die Cavity with Back Taper Opening by Using CAXA. ME 3D Software
利用CAXA.ME三维软件加工倒锥口型腔
On Design of 1000 m~3 Reverse Cone-shaped Water Tower
浅谈1000 m~3倒锥壳水塔的设计
Controlled Blasting Demolition of 38 m High Reverse Cone-shape RC Water-tower
38m高倒锥形钢筋砼水塔控爆拆除
Discussion on Structure Design of 500 m~3 Inverted Cone Water Tower of Glass Plant
浅谈玻璃厂500m~3倒锥壳式水塔的结构设计
Design and improvement of injection mould about back taper raised dome
关于带有倒锥凸起圆盖注射模的设计与改进
Formation of freshwater lens in islands and evolution rules of the upconing
海岛淡水透镜体形成及倒锥演变规律分析
A Novel Method for Measurement of Micro-drill’s CWT
微型钻针内芯倒锥度测量新方法的研究
Study and Practice on the Cycloid Rotational Indexing Technology for Machining the Back-angled Shifterstops of Automobile Synchronizer Sleeves;
汽车同步器齿套倒锥摆线旋分加工技术研究与实践
A Study and Practice on Cycloid Based Machining for the Back Angle of Automobile Synchromesh Sleeves;
基于摆线原理的汽车同步器齿套倒锥加工工艺研究与实践
Briefly account of revision and problems taking into consideration of" national standard drawing far reinforced inverted- cone type water tower(04 S802)" are introduced in this paper.
本文简要介绍“钢筋混凝土倒锥壳水塔标准图集”(4S802)标集修编和所考虑的问题。
Having the shape of a cone resting on its apex.
陀螺形的形状象陀螺或倒置的圆锥的
Study on the Tooth Crest Chamfering Model of Bull Gear of Spiral Bevel Gear Pair;
弧齿锥齿轮大轮齿顶倒角加工模型研究
Research on the Method of Addendum Lines Chamfering for Driven Gear in Spiral Bevel Gear Pair;
螺旋锥齿轮副大轮齿顶线倒角加工方法的研究
Construction Technology of Mass Reinforced Concrete of Inverted Cone-shaped Hopper
大体积倒圆锥形钢筋混凝土漏斗施工技术
Research and application of deflecting bucket with the warped surface conic shaped and hung inversely of ski run of the Shuangdao hydropower station
爽岛水电站滑雪道锥面帖角倒悬扭曲面挑坎的研究应用
Research of Spiral Bevel Gear Chamfering Equipment Based on 6-HTT Parallel Manipulator
基于6-HTT并联机器人的螺旋锥齿轮齿顶倒角设备研究
Let's do an experiment: Two pupils, please. Please pour into a cylinder with a taper full of water. How many times can we fill up the cylinder?
师：下面我们来做一个实验。请两个同学上来演示，将圆锥装满水倒入圆柱，几次可以将圆柱装满？
Series of conical tapers and taper angles
GB/T157-1989锥度与锥角系列
