Aiming at solving the serious problem resulting from the displacement function of the geometric non-linear bent cantilever and its great error ,the author has the function deduced from approximate calculation and Galerkin integration.
针对以往几何非线性悬臂弯曲的位移函数公式繁琐或计算结果误差较大的问题,通过近似并利用加辽金积分推导得出其位移函数。
Research of actuation characteristic of a curved cantilever electrostatic actuator;
弯曲悬臂梁静电执行器驱动特性的实验研究
Specimen for surface crack growth by loading at cantilever bend and application
一种悬臂弯曲加载表面裂纹扩展试样及其应用
Bending behaviors of functionally gradient piezoelectric curved cantilever was studied.
研究了弯曲型梯度功能压电悬臂梁的弯曲特性。
Research on bending of the cantilever based on the principle of minimum potential energy
基于最小势能原理的悬臂梁弯曲研究
BOUNDARY INTEGRAL FORMULA FOR BENDING OF CLAMPED SEMI-INFINITE PLATE
悬臂半无限大板弯曲的边界积分公式
Research of actuation characteristic of a curved cantilever electrostatic actuator
弯曲悬臂梁静电执行器驱动特性的实验研究
Hamiltonian system approach to bending problem of viscoelastic cantilever-beams
粘弹性悬臂梁弯曲变形的哈密顿体系方法
Fourier analysis of bending of orthogonal anisotropic rectangular thin cantilever plate
正交各向异性矩形悬臂薄板弯曲的傅立叶分析
The pouring construction technology of small radius flat curve continuous steel bridge cantilever
小半径平弯曲线连续刚构桥悬臂浇筑施工技术
Simulation Analysis and Curing Effect Research of Curved Continuous Rigid Frame Bridge during Cantilever Construction;
曲线连续刚构桥悬臂施工阶段的仿真分析及弯曲效应研究
overhung cold roll forming machine
悬臂辊式冷弯成型轧机
knee-braced bracket
拐弯托座，膝形悬臂托架
Bending deformation of microscale cantilever has been investigated using an atomic force microscope( AFM).
采用原子力显微镜测试了微悬臂梁构件的弯曲变形规律。
flex one's stiff arm slowly
慢慢弯曲僵硬的手臂
Abstract: Using the united method in this paper, the bending solution of the rectangular plate with one edge built-in and one or two corner point supported can be derived under arbitrary load.
文摘:本文的统一解法可以解决悬臂板或带有角点支承时在任意荷截作用下的弯曲。
The First six natural frequencies of a cantilevered triangular bending plate are calculated both by the conventional finite element and by the second order linite dynamic element.
用常规有限元和二次动态有限元解算了一个悬臂三角形弯曲板的前六阶固有频率。
Using the united method in this paper, the bending solution of the rectangular plate with one edge built-in and one or two corner point supported can be derived under arbitrary load.
本文的统一解法可以解决悬臂板或带有角点支承时在任意荷截作用下的弯曲。
It is found that non-zero normal stresses exist in the gradient piezoelectric curved cantilever when the cantilever is subjected to an external voltage.
研究表明，当受外加电压作用时，弯曲型梯度压电悬臂梁中存在非零的应力。
The Study and Design of Arm Robot for Hull Shaped Plate Forming by Line Heating;
水火弯板成型单悬臂机器人设计分析
