The deflection angle of tapered roller bearings is one of the most important parameters in design and application of rolling mill bearings.
针对轧机轴承的偏斜角在其设计及应用中的重要性,以单列圆锥滚子轴承在额定动载荷作用下、偏斜角为2′时求得的接触应力和接触变形为已知条件,应用Hertz理论,提出求解轧机用重型四列圆锥滚子轴承偏斜角的方法,为轧机轴承的设计提供了理论依据。
Elastohydrodynamic lubrication(EHL) theory was applied to investigate the effect of inner lubrication behavior on service-life of the rolling mill bearings under heavy load,and the approaches to increase service-life via improving lubrication capacity were analyzed with oil film parameter theory and correction life theory.
采用弹性流体动力润滑理论分析了润滑对重载轧机轴承使用寿命的影响,并用油膜参数理论和修正寿命理论研究了改善润滑、提高使用寿命的途径。
The process and properties of 77752 rolling mill bearing made by 100CrMo7 steel bainite hardening were introduced.
介绍了 1 0 0 Cr Mo7钢制 77752轧机轴承的贝氏体淬火处理工艺及其性能 ;用 1 0 0 Cr Mo7钢制轧机轴承进行贝氏体淬火代替 G2 0 Cr2 Ni4A钢制轧机轴承渗碳淬火 ,具有良好的经济技术效益。
Because of fitting rolling mill before 250mm rolling mill,rolling pass increasing to 17 from 10～12 and taking bearing mill,the highest rolling speed of finished mill increasing to 7 1m/s from 5 5m/s,the process request of once heating into product is meeted.
在２５０ｍｍ轧机前增设轧机，将轧制道次由１０～１２道提高到１７道，并用轴承轧机替代原胶布瓦轧机，成品轧机最高轧制速度由５。
This bearing limit rotational speed is low, (therefore mainly applies on the mill calls rolling mill bearing).
该轴承极限转速较低，主要应用于轧钢机上（故称轧机轴承）。
Description: the product we showed is SENDZIMIR Rolling Mills Bearing.
我们展示的是高速线材轧机轴承，即森吉米尔轧机轴承。
The Design and Application of 550mm Tri-roller Rolling Element Bearing Close-top Housing Rolling Mill
Ф550中轧三辊闭口式滚动轴承轧机的设计与应用
General technical requirement of oil film bearing for rolling mill
GB/T13345-1992轧机油膜轴承通用技术条件
Application of Filmatic Bearing Oil on High-speed Rod-rolling Mill
油膜轴承油在高速线材轧机上的应用
Analysis of Lublication and Failure for Thrust Bearing in Cold Mill Main Motor
冷轧主电机止推轴承润滑与故障分析
Influence of misaligned journal bearings on the start-up process of tandem cold rolling mills
油膜轴承倾斜承载对冷连轧机启动的影响
Domestic Research on Large-Size TQITSE Bearing Used on Supported Roller of Imported Cold-Rolling Mill;
进口冷轧机支撑辊用大型TQITSE轴承国产化研究
Study on Oil Film-Roller Combination Bearing of φ200 Cantilever Finishing Mill;
φ200悬臂式精轧机油膜—滚子组合轴承开发研究
RESEARCH OF WORK ROLL CHOCK DYNAMIC CHARACTERISTICS ON 2350ALUMINIUM FOIL MILL;
2350铝箔轧机工作辊轴承座动态特性研究
FEM Analysis of the Four-Row Tapered Roller Bearing of Vertical Miller;
立辊轧机四列圆锥滚子轴承有限元分析
Analysis and research of the breaking of the thick plate rolling mill oil taper sleeve
特厚板轧机油膜轴承锥套断裂原因分析与研究
Application of Oil-air Lubrication Technology in Work Roll Bearings of Cold Rolling Mill
轧机工作辊轴承油气润滑技术应用分析
Hydraulic Control System Design of Roll-chock Putting in and out Machine
轧辊轴承座拆装机液压控制系统的设计
Advanced Technique Applied in The Lubrication System of Oil Film Bearing at Stechel Mill in Anyang Iron and Steel Group Co.
先进技术在炉卷轧机油膜轴承润滑系统的应用
The bearing GZU cold-rolld and twisted steel machine for monitor research online
GZU钢筋冷轧扭机组轴承故障诊断仪的研究
RESEARCH ON SPLIT BEARING OF KPW75VMR HIGH-SPEED COLD ROLLING MILL AND DOMESTIC MODIFICATION
KPW75VMR高速冷轧机剖分轴承研究及国产化改造
Failure Analysis on Bearing with Dowels Welded to Frame in Huge Roll Mill
大型轧机柱销焊接保持架轴承失效分析
