Pressure adjustment of hermetically sealed relay spring by laser-forming
密封继电器弹簧片压力的激光校正研究
This paper introduces the test of optimum heat treatment process scheme of starting spring of the FQ type engine.
通过试验找出了FQ型发动机启动器弹簧片最佳热处理工艺。
The principle of the 憇nake-type spring is analyzed.
阐述了300 MW汽轮机高压缸动叶顶部汽封的基本结构及改进形式,并对“蛇型” 弹簧片的工作原理做了理论性的分析。
The casing centralizer with segmented spring leafs is the casing hardware most often utilized, in which the casing centralizer with single segmental spring leaf is common used.
弓形弹簧片套管扶正器是使用量最多的套管附件,其中单弓形弹簧片套管扶正器是使用最普遍的;双弓形弹簧片套管扶正器是单弓形的变异,它具有弹性扶正器的优点,又有刚性的特点。
The technological property of the auto clutch spring plates is analyzed.
分析了汽车离合器弹簧片的工艺性,介绍了一种可提高材料利用率及提高工效的少无废料自动送料复合模结构。
Relationship between spring plate and the measured value stability of precise meter was introduced, improvement in spring plate and results achieved were also presented.
介绍弹簧片与仪表示值稳定性的关系、弹簧片的改进方法及效果。
The structure of existing spring strip is introduced and a new feasible concept is proposed on the basis of calculations.
介绍了弹簧片现有结构,通过计算,提出一种可行的新设想。
the working principle of the spring strip of sealing ring for steam turbine is presented and an analysis is made on the strength check of "diamond" shape spring strip.
阐述了汽轮机汽封圈弹簧片的工作原理,并对"菱型"弹簧片的强度校核做了推导和分析。
Through analyzing on the structure characteristics of the spring piece, designed a automatic feed progressive die.
通过分析弹簧片零件的构造特点,设计出了一幅自动送料的级进冲模。
Fracture Failure Analysis of Pressing Spring for Rearview Mirror
汽车后视镜压入弹簧片断裂失效分析
The Design and the Experimental Research of the Z Style Spring Piece of Piezoelectricity Vibration Feeder
Z型弹簧片压电振动送料器的设计与实验研究
a pocketknife with a spring-operated blade.
有弹簧折叠刃片的小刀。
spring loaded apex seal
弹簧加载径向密封片
Leaf Spring Remove/Install
叶片弹簧之拆卸、安装
"There are two types of leaf spring, the multileaf and the single leaf."
钢板弹簧有两种,多叶片钢板弹簧和单叶片钢板弹簧。
Tighten leaf spring press until bushing is extracted from leaf spring.
上紧叶片弹簧加压机直到衬套被拔出叶片弹簧。
Clutch Type Single sheet, dry type, film spring
离合器型式：单片、干式、膜片弹簧
Elastic damping leaf coupling
GB/T12922-1991弹性阻尼簧片联轴器
Elastic damping leaf damper
GB/T14654-1993弹性阻尼簧片减振器
The Design of Diaphragm Spring Clutch
膜片弹簧式离合器的分析及优化设计
"Cushion springs. If the cushion springs under the facings appear to be cracked or weak, the friction disk should be replaced."
缓冲弹簧:如果衬片下的缓冲弹簧出现裂纹或磨损,摩擦盘也应更换.
"Three types of clutch are the coil-pressure-spring type, diaphragm-spring type, and semi centrifugal type."
离合器的三种类型为:螺旋弹簧式,膜片弹簧式和半离心式。
Influence of Elastic Modulus toValves Designing Parameters of Hydro-Pneumatic Spring
阀片弹性模量对油气弹簧阀系设计参数的影响
Study on Superposition Throttle-Slice and Opening Valve Pressure of Hydro-pneumatic Spring
油气弹簧多片叠加节流阀片与开阀压力研究
Produce primarily now the every variety spring, spring layered, rammed res and divided by the iron tool product.
现主要生产各类弹簧、簧片、金冲压件及除铁工具产品。
Tighten leaf spring press until bushing flange bottoms solidly against leaf spring eye.
上紧叶片弹簧加压机直到衬套凸缘的底部扎实地扺住叶片弹簧的孔眼。
Bend the bushing tabs so that they are contacting the leaf spring.
弯曲衬套接头以便接头能与叶片弹簧接触。
