Study on contact damage of sleeve of oil-film bearing in rolling mill;
大型轧机油膜轴承锥套损伤问题研究
The Oil-film Temperature Fild Analysis of Oil-film Bearing Based on ANSYS;
基于ANSYS的油膜轴承油膜温度场分析
This paper presented the mechanism of fretting fatigue failure that happened on the contact surfaces between sleeve and roll neck of oil-film bearing under the rolling load.
研究了油膜轴承锥套与辊颈接触表面在轧制载荷作用下发生微动疲劳损伤的力学机理。
Design and analysis of structural parameters for capillary oil film bearing
毛细管节流的油膜轴承结构参数设计分析
A modern large-scale mill's perfect bearing——oil film bearing,a key part of the mill,has many advantages,such as large carrying capacity,long service life,wide speed range,low friction coefficient,small configuration size,strong impact resistance,etc.
现代大型轧机的理想轴承——油膜轴承是轧机的关键部件,具有承载能力大、使用寿命长、速度范围广、摩擦因数小、结构尺寸小、抗冲击能力强等优点。
Baosteel Branch's 5m mill is the first especially wide and heavy plate production line,and oil film bearing is one part of its main equipment.
宝钢分公司厚板厂5m轧机是国内第一条特宽幅厚板生产线,油膜轴承是厚板轧机的主要设备之一,正确认识和掌握其特点是提高厚板生产的关键环节。
The partially alloyed CuSn10 powder for high speed,low noise and self lubricating bearingshad been successfully developed by Cu Sn alloying process The characteristics of powders were investigated by SEM The influence of powder mixing process,green density,diffusion time and temperature on the properties of powders were discusse
本文通过对电解Cu粉、雾化Sn粉的部分合金化过程的研究 ,制备出适于制造高速、低噪音、微型含油轴承的CuSn1 0部分合金化粉末。
Comparing research has been done between Fe Cu and bronze P/M oil bearings for odometers.
本文针对里程表用含油轴承 ,对粉末冶金铁 铜和青铜材料进行了对比研究。
Application of Filmatic Bearing Oil on High-speed Rod-rolling Mill
油膜轴承油在高速线材轧机上的应用
General technical requirement of oil film bearing for rolling mill
GB/T13345-1992轧机油膜轴承通用技术条件
Static Testing Investigation of Controllable Hydrodynamic Bearing with Gaint Magnitostrictive Actuator
GMA可控油膜轴承的静态试验研究
Influence of misaligned journal bearings on the start-up process of tandem cold rolling mills
油膜轴承倾斜承载对冷连轧机启动的影响
A Study on the Seal of HAGC Cylinder and Oil Film Bearing of Backup Roll
HAGC油缸和支承辊油膜轴承用密封件的国产化研究
Design and Accomplish of Visual Performance Calculation System of Oil-film Bearing
油膜轴承可视化性能计算系统的设计及实现
To Keep Technological Superiority Is the Base of Continuous Development of Taizhong Oil Film Bearing;
保持技术优势是太重油膜轴承持续发展的根本
Analysis and research of the breaking of the thick plate rolling mill oil taper sleeve
特厚板轧机油膜轴承锥套断裂原因分析与研究
Advanced Technique Applied in The Lubrication System of Oil Film Bearing at Stechel Mill in Anyang Iron and Steel Group Co.
先进技术在炉卷轧机油膜轴承润滑系统的应用
Design and analysis of structural parameters for capillary oil film bearing
毛细管节流的油膜轴承结构参数设计分析
Development of the Loaded State of Oil Film of Wire Stock High-speed Rolling Mill and Simulation Test System;
线材高速轧机油膜轴承承载状态与仿真测试系统开发
Shaft Assembly (Male, female, washer, grease….
轴组件（轴，轴套，轴承，油脂。。。）
Analysis on Measurement Approach for Lubricant Film Thickness of Sliding Bearing
滑动轴承润滑油膜厚度测量方法分析
Calculation of the influences of marine shafting dynamic alignment affected by bearing oil film
船舶轴系动态校中轴承油膜的影响计算
The Research on Oil Film Rupture Regular of Novel Spiral Oil Wedge Hybrid Journal Bearing
新型螺旋油楔动静压轴承油膜破裂规律的研究
"To minimize friction, the contacting surfaces in a Bearing may be separated by a film of oil or gas, these are also sliding Bearings ."
为了减小摩擦力,轴承内的两个接触面可以用一层油膜或气膜隔开,这类轴承称作滑动轴承。
Study on Oil Film-Roller Combination Bearing of φ200 Cantilever Finishing Mill;
φ200悬臂式精轧机油膜—滚子组合轴承开发研究
Development of Journal Bearing Test Equipment and Measurement of Oil Film Pressure;
滑动轴承试验装置开发与油膜压力测量
