Microstructures and thermal stability of ultrafine-grained Al-1%Mg alloy produced by accumulative roll-bonding process;
叠轧深变形制备的超细晶Al-1%Mg合金组织与热稳定性
The Electrodeposited coating can eliminate the compounded interface of accumulative roll-bonding;the paper gives a elementary analysis of the theory about the compounded processor.
控制电解沉积过程在纯铜的表面制得宏观上致密、光滑的铜镀层,以此镀层来消除叠轧金属层间的复合界面;对此镀层消除叠轧金属层间复合界面的机理进行初步的分析;并应用有限元软件对轧制过程进行计算机模拟分析,验证提出的机理;得出镀层材料塑性变形程度大,有利于消除金属层间复合界面;镀层不引起界面处塑性变形热效应的明显变化。
Accumulative Roll-Bonding process has a potential application for commercial production of ultrafine-grained materials.
叠轧深变形技术具有商业化生产超细晶材料的潜力。
Status and expectation of research on accumulative roll-bonding;
累积叠轧技术的研究现状与展望
The evolution of microstructure and mechanical properties of AZ31 sheets during accumulative roll-bonding was researched.
采用累积叠轧工艺对AZ31镁合金薄板进行剧塑性变形,研究了累积叠轧变形过程中镁合金板材的组织及性能演变。
The influence of pack ply-rolling process and heat-treatment on the microstructure, tensile properties and fatigue properties of Ti-6Al-4V alloy sheets was studied .
研究了包覆叠轧加工及热处理工艺对Ti-6Al-4V合金室温拉伸及疲劳性能的影响规律,观察分析了不同状态下组织形貌的特征及变化情况。
Study on the manufacture sub-micron metal materials by severe deformation of ARB process
累积叠轧焊强加工制备亚微米金属材料的研究
Al/AZ31 Multilayered Composite Prepared by Accumulative Rolling Bonding Technique and Its Strength
累积叠轧焊制备Al/AZ31多层复合材料及其强度
Preparation of Ultrafine Grain Magnesium Alloy by Accumulation Roll Bonding and Microstructure Refinement Mechanism;
累积叠轧焊法制备超细晶镁合金及组织细化机制研究
imitation beetle calender
仿捶布轧光，仿叠层轧光
beetler calender, beetling calender
叠层轧光机,捶布轧光机
made or become wrinkled as by crushing or folding.
通过轧压、折叠而制成或变成皱的。
Study on Edge Folding Control for Hot-rolled Strip Ultra-low Carbon
热轧超低碳带钢边部折叠控制的研究
Specification for design and construction of concrete superposed key slabs with cold-rolled and twisted bars
键式冷轧扭钢筋混凝土叠合板设计与施工规程
In this paper, we study on the laminating technology for cold-rolled silicon steel sheet through a number of tests.
本文通过一系列试验,对冷轧硅钢片铁心叠压中的有关工艺问题进行了研究。
To press with a mangle.
轧压用轧布机来轧压
combination blooming billet mil
初轧-轧坯联合轧机
according to the temperature of the metal being rolled, rolling processes can be classified as hot rolling and cold rolling. and the rolled products can thus be specified as hot rolled or cold rolled products.
根据轧制轧材的温度，轧制可分为热轧和冷轧;因而轧制产品也可分为热轧产品和冷轧产品。
laboratory mangle, laboratory padder
试验室用轧车，小轧车
The train chugged along.
火车发出轧轧声前进。
The sewing machine hums busily.
缝纫机忙碌地轧轧响着。
huller roll - box
气流式轧花机的轧辊箱
mandrel-cambered bowl
中高轧辊,凸芯轧辊
central supporting bowl
中固轧辊,中支轧辊
