This article introduces a design of compound mold using for water tank panels.
本文设计了一款水箱面板的复合模,该复合模采用压力机上下油缸同时压制坯件成型,代替了原来的两套模具,大大减少了模具成本。
Over analyzing the structure and character of the case panel, the general structure design project of its injection mold is determined, as well as the design of feed system, slide side-drawing mechanism, slanting pin mechanism, ejector system and inserted mechanism are stated in details.
通过对机箱面板结构及特点的分析,确定了其注射模具的总体结构设计方案,并对浇注系统、滑块侧抽机构、斜销机构、顶出系统以及镶块结构的设计进行了详细论述。
On That the Radian of Both Faceplate and Soleplate of Violin Resonator Influence Upon the Librations Features;
小提琴共鸣箱面板和底板弧度对振动特性的影响
double-skin pontoon hatchcover
底面铺板箱形舱口盖
The Finite Element Method of Bridge Continuous Box Girder Beam and T Tepth Beam;
箱梁、T型断面梁的空间板有限元解法
turning-over board
翻箱板，造型平板，底板
The suitcase bursts open and its contents rained on the floor .
手提箱裂开了,里面的东西纷纷落在地板上
The suitcase burst open and i... contents rained on the floor.
手提箱裂开了，里面的东西纷纷落在地板上。
The bents supporting the four continuous 工 beam plate girders have a cross section shaped like a box.
构架支承着四片工字型板梁，构架的截面为箱型。
RESIDUAL LIFE ANALYSIS OF THE SKIM PANEL OF AH-24 WING INTEGRAL TANK WITH CRACKS
安—24机翼油箱含裂纹面板的剩余寿命分析
Technology of Concrete Whole Box Girder Prestressed Strengthening
混凝土整体截面箱形(板)梁桥预应力加固技术
Wheel Load of Bridge Deck of Large-Span Continuous Composite Box Girder
大跨连续组合箱梁桥面板轮载作用分析
Study on Coatings Property of Precoated Steel Sheet Used for Refrigeration Container
冷藏集装箱用彩色涂层钢板表面涂层性能研究
Design of Fully-welded Steel Plate Composite Truss Girders of Box Section Member Bar of Minpu Bridge Ⅱ,Shanghai
闵浦二桥箱形截面杆件全焊钢板组合桁梁设计
coffin annealing
(钢板的) 装箱退火
composite wood and fiberboard container
木板、纤维板合制集装箱
Remove the glove box inner door panel from the glove box outer door panel.
从手套箱外门板上拆下手套箱内门板。
CZ-JB junction box produced with Bao Steel A3 material with painting after surface finish.
JB接线箱采用宝钢产A3板材进行加工生产，表面加工处理后喷漆。
CZ-JB junction box is produced with Bao Steel A3 material with surface finish of paining and plastic spray.
JB接线箱采用宝钢产A3板材进行加工生产，表面处理烤漆、喷塑。
We'll reinforce the boxes with straps and line them with plastic sheets.
此外，我们在纸板箱内衬塑料膜，在外面用条带加固。
