Warm-hot control forging of automobile spline shaft;
汽车花键轴温热控制精锻工艺
The Earlier Period Failure Analysis of Spline Shaft for a 4-Roll Rolling Mill;
四辊轧机花键轴早期失效分析
The authors confirm that breaking mechanism of spline shaft is fatigue breaking, and put forward corresponding measures to solve the problem from the aspects of designing, material choosing, manufacturing, and controlling quality etc, it is recognized in manufacturing spline shaft, 50CrMoA should be chosen and tempered with the addition of surf.
在花键轴材料分析及机械性能测试的基础上,通过花键轴载荷分析,利用Pro/E和Pro/M对花键轴进行强度和疲劳寿命分析,证实花键轴的断裂机理就是疲劳断裂,并从设计、材料选择、加工制造、质量控制等方面提出了针对性的措施,认为:在改进设计和制造蜗杆花键轴时,应该选用50CrMoA,调质处理加表面淬火,控制钢中的S、P、Cu含量,适当加大花键轴的直径,同时加大齿根圆角半径,以提高花键轴强度和寿命。
The cold extrusion process for the spline sleeve of GCr15 steel was analyzed.
对GCr15钢花键轴套零件的冷挤压工艺进行了分析 ,制定了先正挤花键后镦挤球头体的挤压方案 ,并介绍了该零件的冷挤压模结构及其特
Using the given method and conclusion of the stress field solutions of shafts under torque loadings, this paper analyzes theoretically the mechanisms of the cracking initiating orientation of splined shafts and their physical appearance of fracture.
本文用业已建立的轴类零件受扭时应力场解析的方法和结论，对作间歇回转运动设备中的主轴——花键轴的断裂机理进行了研究分析；建立了裂纹源的键齿根应力集中处的主应力和主平面分析数学模型；指出了断口裂纹萌生方向；以及在高速间歇运动工况下，断口的宏观呈象为犬牙交错。
Spline shaft grinding machines-Parameters
GB/T10930-1989花键轴磨床参数
Splint hobbing machines-Testing of the accuracy
GB/T9167-1988花键轴铣床精度
Processing Method of a Spline Shaft of German DMC64V NC Milling Machine
德国DMC64V数控铣床某花键轴的加工
Crack reason analysis on SAE1141H steel spline shaft after heat treatment
SAE1141H钢花键轴热处理后开裂原因分析
Numerical simulation of spline in cold rolling based on DEFORM-3D
以DEFORM-3D实现花键轴精密冷滚轧成形模拟
The machine is suitabe for largebatch, small batch and single production of cylindrical spur and helical gears worm gears sprocket and spline shaft in certain range of parameters.
*该机床适用于成批、批及单件生产加工圆柱直齿轮、柱斜齿轮、轮和一定参数的花键轴。
Influences of spline coupling on stability of rotor-bearing system
花键联轴器对转子-轴承系统稳定性影响研究
Research on Cold Extrusion Forming Technics of Micro-vehicle's Half Axle Spline
微型车半轴花键冷挤压成形工艺研究
Study on Three Dimension Modeling Method for Involute Spline of Torsion Shaft
扭力轴渐开线花键三维建模方法研究
Study of Impact on the Stress of Spline Axis when Selecting Material of Electric Submersible Pump Set
潜油电泵花键套材料选用对泵轴应力的影响
Analysis on the Fracture of Two Drilling Jar's Splined Mandrel and Improvement Measures
2起震击器花键心轴断裂原因分析及改进措施
Dynamic behavior of a rotor-misaligned spline coupling system
转子-不对中花键联轴器系统动力学特性研究
six-keyway broach
六键拉刀, 花键拉刀
"Turn the shaft, if the clutch-disk hub splines. Put Bolts in place, and tighten them to the correct tension."
如果与离合器从动盘轮彀的花键相连,可转动传动轴,把螺栓就位,并适度拧紧。
There must be one or more universal joints to permit variations in the angle of drive. There must also be a slip joint that permits the effective length of the propeller shaft to change.
一个或几个万向节来适应传动角度的变化;一套伸缩花键,能够改变传动轴的现有长度。
Create a Rotation Key on
创建Y轴的旋转关键帧
Create a Rotation Key on Z
创建Z轴的旋转关键帧
