Forming process and design of die for shaft cup;
轴盖成形工艺与模具设计
In the paper, the 3D design process of the bearing cap progressive die was mainly described based on Solid Edge V17.
主要叙述了基于Solid Edge V17平台实现轴承盖级进模三维设计的过程。
Through the retrofit of large and middle scale motor shaft-extensio n end bearing cap,XinYu power plant divides shaft-extension end bearing cap of mo tor with bearing stand into upper and lower parts.
新余发电有限责任公司通过对大、中型(滚动轴承)电动机轴伸端轴承盖进行改造,将有轴承座的电机的轴伸端的轴承盖分上、下两部分剖开的改造工艺可方便轴承盖的拆装,在电机运行异常时,便于及时检修,可以大大减少电动机设备的损坏事故。
Production cost is vital to an enterprise ,how to control production cost is the most important,the paper introduces the optimal design of the mold of bearing cap for roto
生产成本对企业至关重要,如何控制生产成本成为企业头等大事,本文重点介绍了海马汽车中一个叫转子轴承盖模具的最优化设计。
Development of a main bearing cap for an inline 6 cylinder engine;
一种直列式6缸发动机主轴承盖的开发
Problems of falling chip, tool tipping and big noise are happened during cutting off main bearing caps made of gray casting by using combination milling cutters.
采用组合铣刀切断灰口铸铁材质的汽车发动机主轴承盖时 ,出现工件掉渣、刀具崩刃、噪声大等问题。
The characteristic analysis of the suspended main bearing cap of SL4105 diesel engine was presented by using the 3D solid modeling,3D mesh generation,external loads & boundary condition and 3D finite element analysis.
介绍一种运用三维实体造型、三维网格划分、载荷和约束处理及三维有限元分析的方法,对SL4105柴油机悬挂式主轴承盖进行了强度和刚度分
Screw, crank cover
曲柄轴盖子固定螺丝
Insert Timing Case Cover Alignment and Seal Installation Tool 6139 in the crankshaft opening in the cover .
在曲轴盖的开口处，插入正时箱盖定位和轴封安装工具6139。
Remove the floor console from the floor pan transmission tunnel.
从底板变速器-传动轴盖板中拆去底板支柱。
Remove the lower insert from the bearing cap.
从轴承盖上拆去下轴瓦。
Install the lower bearing inserts into the main bearing caps.
安装下轴瓦到主轴承盖。
end shield bearing
机油滤清器内盖头轴承
Analysis and solution of cramped shield to be detachable in sealing bearings
带卷边防尘盖轴承活盖问题解决办法
The rod-bearing cap attaches the connecting rod to the crankpin.
连杆轴瓦盖将连杆安装到曲轴销上。
hub cap for road motor vehicles or tractors
轴端盖,道路机动车辆或摩托车用
The cover provides a means for servicing the differential without removing the axle.
通过盖可维护差速器，不用拆卸轴。
Install pitman shaft and side cover in the housing.
在机座中安装转向摇臂轴和侧盖。
The fresh-air inlet was usually the crankcase breather cap.
新鲜空气进口一般是曲轴箱通气盖。
Install the engine cylinder head, push rods, rocker arms, bridges, pivots and engine cylinder head cover.
安装引擎汽缸盖、推杆、摇臂、桥、枢轴和引擎汽缸盖罩。
The cap and rod have bearings which permit the crankpin to rotate freely within the rod.
轴瓦盖和连杆中有轴瓦，它允许连杆内的曲柄锁自由地转动。
The bearing shells must be installed so that the tangs are in the machined grooves in the rods and caps.
安装轴瓦时，应使凸舌位于连杆和轴承盖的加工槽内。
Remove the depth shims from rear pinion bearing cup bore in axle housinRecord the thickness of the depth shims.
从轴管里的后小齿轮轴承盖孔拆卸限深垫片。记录限深垫片厚度。
Measurement of Dynamic Stresses and Temperatures of Main Bearing Walls and Caps on an Engine Block
发动机缸体主轴承座及主轴承盖的动态应力和温度测量
Place 4 adapter blocks so they do not damage the bearing cag
安装4个接头垫块，以免损坏轴承弹子盘盖。
