This paper provides a principle optimizing the coat hanger die with the tear shape manifold and a method simulating the distribution of pressure in the die cave.
阐述了泪滴型歧管衣架机头流道优化计算原理和压力分布模拟计算的方法 ,编制了CAE软件包。
According to the mechanism and pressing process of sintered NdFeB magnet,the distribution of pressure during pressing process was analysed and derived,which is helpful to determined the pressing direction and the size of mold.
根据烧结钕铁硼永磁材料压制成型机理及压制成型工艺,分析了压制成型过程磁粉受力情况,推导出压制成型的压力分布公式。
A principle optimizing the L die with the genetic algorithms and a method simulating the distribution of pressure in the die cave are provided.
讨论了L型机头流道主要参数对挤出压力分布均匀性的影响 ,并将本计算模块应用于工业实践。
Calculation of pressure distribution in intermittent producing test well with δ Function;
利用δ函数计算间歇试采井压力分布
Subjective assessment of pressure distribution for sports underwear;
运动内衣压力分布的主观评定
Exact and simple method for calculating pressure distribution in deep gas condensate well with high temperature and pressure;
深层高温高压凝析气井压力分布的简便算法
The method to calculate pressure distributing of ultra-thin gas film;
超薄气膜润滑压力分布的计算方法
The results show that the inclined walls and the change of attack angle have great influence on the pressure distributing and St.
结果表明,倾斜壁面和攻角改变对压力分布和St有较大影响。
On the basis of the differential equations of fluid momentum and its mass continuity equation, turbulent pressure distributing function is derived with regard to fluid inertia force.
从运动流体的动量微分方程及其质量连续性方程出发 ,分别采用紊流短轴理论和层流长轴理论来分析挤压阻尼器油膜层和滑动轴承油膜层 ,推导出油膜层压力分布函数 。
To eliminate hydraulic valves noise pressure distributions,cavitation and noise spectrum inside different throttling grooves were studied.
为了消除液压阀中的噪声,对不同节流槽内部压力分布、气穴形态和噪声频谱进行了研究。
On the basis of analyzing three cavity flows,and through the comparison of pressure distributions on cavity flows,it can be seen that the flowfield structure features and the effect of crucial parameters(L/D、W/D、δ_c、δ_h and M) on cavity flowfield structures.
在分析了弹穴3类流动的基础上,利用风洞试验着重研究了弹穴的几何参数(L/D、W/D、cδ、δh)以及飞行参数(M)与弹穴内流场结构间的耦合关系,获得了亚跨超声速来流条件下弹穴底面中心线上的压力分布及弹穴流动特性。
The three-dimensional pressure distributions and temperature field of capillary-compensated,water-lubricated hydrostatic journal bearings with four deep recesses were analyzed.
研究得到了在水介质润滑下的动静压轴承三维压力分布、温度场分布及动特性系数。
density profile,pressure profile
密度分布图,压力分布图
body surface pressure distribution test
车身表面压力分布试验
pseudo steady-state pressure distribution
拟稳定状态压力分布
Research on pressure distribution for full-hydraulic underground coiler machine
全液压地下卷取机卷筒压力分布研究
Pressure Distribution and Energy Dissipation Analysis of Hydrocyclone
水力旋流器径向压力分布及能耗分析
the pressure distribution and scope are related to the fracture azimuth;
压力分布及压力波及范围与裂缝发育方向有关;
Objective Measurement Andlysis of Bra Stress Distribution under Static and Dynamic Status
动静态下文胸压力分布客观测量分析
Theoretical analysis on oil film pressure distribution of squeeze film damper
挤压油膜阻尼器的油膜压力分布理论分析
Optimized Calculation of the Coat Hanger Die and the Simulation of the Distribution of Pressure
衣架机头的优化计算及压力分布模拟
The Pressure Distribution on the Surface of laterference Fit of Retaining Ring and Rotor Body
护环与转子本体配合面上的压力分布
The testification of the reliability of gait impression theory through thenar pressure distribution;
从足底压力分布看步法特征的可靠性
Research on CAD of Shoe-last Based on Foot Pressure Distribution
基于足部压力分布的鞋楦CAD研究
Pressure Distribution of Gaseous Slip Flow in Microchannel
微通道气体滑移流动的压力分布(英文)
Calculation of pressure distribution of flowing foams in porous media
多孔介质中流动泡沫的压力分布计算
Pressure Distribution Characteristics around a Slender Circular Cone at 35° Angle of Attack and Low Speed
20°圆锥低速35°迎角下的压力分布特性
Research on Plantar Pressure Distribution during Walking,Running and Jumping
走、跑、跳动作足底压力分布特征研究
Calculation method of pressure field distributed parameter of hydraulic friction pairs
液压摩擦副压力场分布参数计算方法
The Field Pull-out Tests and Computation of Distribution of Shearing Force of Pressure-type Anchor;
压力型锚杆现场试验及剪力分布计算
