Forging process and design of die for the steering knuckle of truck;
卡车转向节锻造工艺与模具设计
Production of Nodular Iron Steering Knuckles for Micro-car by Shell Mold Casting;
微车转向节系列球铁铸件的壳型铸造
Numerical simulation of car steering knuckle obliterated extrusion forming;
轿车转向节闭塞挤压成形过程研究
FEM analysis of the extrusion-forging compound process for knuckle of Benz heavy truck;
奔驰重卡转向节挤压锻造复合工艺的有限元分析
Forming parameters optimization of knuckle based on Deform;
基于Deform的转向节成形参数优化设计
The Finite Element Analysis and Manufacture Technics of Steyr Knuckle;
斯太尔转向节有限元分析与制造工艺研究
Forging process simulation of steering joint based on finite deformation theory;
基于有限变形的转向节锻造成形过程模拟
Calculation of deforming force about the steering joint;
转向节成形变形力的计算
In order to study the reliability of mine automobile steering joint,the calculation finite element model of aluminium alloy wheel type was established in the Solidworks software.
以STEYR矿用汽车转向节为研究对象,利用Solidworks软件建立了转向节的几何实体模型,在ANSYS中应用蒙特卡洛方法就制动工况进行可靠性有限元分析和影响转向节安全性的灵敏度指标分析,为矿用汽车关键部件设计提供理论指导。
Virtual Modal Analysis and Validation of Automobile Steering Knuckle;
轿车转向节柱虚拟模态分析及验证
steering knuckle tie rod end pressure lubricator
转向节横拉杆接头油嘴
steering knuckle bearing grease nipple
润滑转向节轴承油嘴
Install the brake rotor shield to the knuckle.
向转向节上安装煞车分火头护罩。
steering knuckle tie rod end assy
转向关节横拉杆接头总成; 转向节横拉杆接头总成
Many types of steering linkage have been made to connect between the steering knuckles of the front wheels and the pitman arm of the steering gear.
很多类型的转向连杆装置都是用来连接前轮转向节和转向器的转向摇臂的。
Finite Element Simulation of Process for Automobile Steering Knuckle;
汽车转向节成形工艺有限元模拟研究
CAE Optimization of the Forging Process of Automobile Steering Knuckle;
利用CAE技术改进汽车转向节锻造工艺
A Study of Forging Forming Process for Steering Knuckle of Light Truck
轻卡汽车转向节锻造成形工艺的研究
HyperWorks Application in Optimization Design of Auto Knuckle
HyperWorks在汽车转向节优化设计中的应用
Hot Forging Process and Die Design for 1041 Knuckle
1041转向节热模锻工艺及模具设计
Route sensor wire from steering knuckle to fender panel.
从转向节到防护板安排感知器导线走向。
This movement is produced by gearing and linkage between the steering wheel in front of the driver and the steering knuckle (or wheel).
这一运动是由装在驾驶员前面的转向盘与转向节(车轮)之间的转向器和连杆装置来共同完成的。
Tie Rod End To Steering Knuckle Nut
转向拉杆端与转向关节螺栓
steering wheels adjustment control
转向盘调节装置操纵件
steering arm adjusting screw wrench
转向臂调节螺钉扳手
Steering Knuckle Separation From Driveshaft
转向关节与驱动轴分离
Clevis Bracket To Steering Knuckle
U型环支架至转向关节
Remove the steering knuckle from the strut.
自支柱拆除转向关节。
