Based on the test of 14 model slabs, this paper analyses the property in applied stage and the failure pattern of slabs reinforced with 550 cold rolled deformed bars, and presents the strength design value of the bar.
根据１４块模型板的试验，对５５０级冷轧带肋钢筋混凝土板使用阶段的性能及破坏形态进行了分析，并提出了该种钢筋的强度设计值。
Based on the tests of 16 model beams,the paper analyses the properties of failure pattern of beams reinforced with LL550 cold rolled deformed bars in applied stage, and presents the strength design value of the bar.
根据１６根模型梁的试验，对ＬＬ５５０级冷轧带肋钢筋混凝土梁使用阶段的性能和破坏形态进行了分析，并提出了该种钢筋的强度设计值。
It has been discussed that the value of improvement factor of part compressive strength,design value of compressive strength in part compressive strength calculation of masonry structure and the antiknock bearing capacity proven of the reinforced brick masonry;and some corresponding suggestions are presented.
就砌体结构局部受压计算中局部抗压强度提高系数、抗压强度设计值的取值及配筋砖砌体构件的截面抗震承载力验算等问题进行了分析,并提出了相应的建议,可供设计时参考。
DISCUSSION AND SUGGESTION ON WHETHER THE INFLUENCE OF PRY FORCE IN THE DESIGN VALUE OF TENSILE STRENGTH OF GRADE C ORDINARY BOLT IN CODE IS CONSIDERED
规范中C级普通螺栓抗拉强度设计值是否考虑撬力影响的探讨与建议
Strength Check and Stowage System Design of Ship Based on Digital Table of Offsets;
基于数字型值表的船舶强度校核及装载仪设计
The emphasis on the minimum nozzle length was carried to the limit with the design of nozzle with sharpedged throats.
强调最小喷管长度转向采用锐边喉管道的喷管设计的极限值。
Designing Ship Intensity & Structure
船舶强度与结构设计
Electric Field Strength Numerical Calculation of the Gradient Doping Semicondouction
梯度掺杂半导体电场强度的数值计算
This value is used to compare the strength of materials, but a safety factor is applied when making design calculations, to bring the working stress well below the limit of proportionality.
此值被用来比较材料的强度，但是当设计计算时，要用一个安全系数，使工作应力低于比例限制。
Experiment Design Ⅱ of Computer Numerical Calculation--Resonance Acceleration of Electrons in Combined Intense Laser Fields and the Spontaneous Quasistatic Fields;
计算机数值模拟实验设计Ⅱ——强激光脉冲对低密度等离子体通道中电子的共振加速
The Strength Fuzzy Reliability Design of the Helical Compression Spring;
螺旋压缩弹簧强度的模糊可靠度设计
Stiffness and Strength Criteria for Design of Buckling-Restrained Braces
屈曲约束支撑设计的刚度与强度准则
Round Link Connector Strength Analysis and Optimization Design;
高强度接链环强度的理论分析及优化设计
Strength Equivalent Design of High Working Semi-trailer Frame by Using The High Strength Steel Plate
高空作业半挂车车架高强度钢板强度等代设计
The euqual strength design of high strength steel plate for great tonnage dump truck box
大吨位自卸车货厢高强度钢板强度等代设计
collapse method of structural design
结构设计的极限强度计算法
Optimization Design of Bearing for Internal Combustion Engine Considering Crankshaft Strength;
计及曲轴强度的内燃机轴承优化设计
Intensity Measure Design of Ultraviolet Light Based on ATMEGA16L;
基于ATMEGA16L的紫外线强度计的设计
Design and strength calculation of main air reservoir for HX_D3B locomotive
HX_D3B型机车总风缸设计及强度计算
Design and Strength Calculation for Heavy Haul Electric Locomotive Carbody
重载电力机车车体的设计与强度计算
Design of High G Accelerometer and Its Read-out Circuit
高g值加速度计及其检测电路的设计
