The service of rubber lining for anticorrosion in production of WPA is introduced, including some key points in design of rubber lining for vacuum equipment, the characteristics of homemade/joint venture/foreign enterprises liner plates and their selection, as well as notices in use.
介绍衬胶防腐在湿法磷酸生产中的应用 ,特别是真空设备设计衬胶防腐的要点以及目前我国湿法磷酸装置中国产 (含合资、独资企业 )胶板的特点和选用、施工中应注意的事项。
The design calculation of the large O ring rubber self energized seal (without bolt and nut )used for the vacuum equipment and its application results are introduced.
介绍真空设备法兰采用大直径Ｏ形环橡胶自紧式密封（不用螺栓和螺母）的设计计算及其应用效果。
This paper introduces application of PP vacuum equipment ,the design and calculation of the vacuum equipment are emphasized .
概述用聚丙烯制作的真空设备的使用情况,着重介绍真空设备的设计与计算,并对不同的计算公式进行了比较,这样便于了解和掌握聚丙烯真空设备的设计和使用。
On the design of vacuum system for external refining equipment of molten steel;
钢液炉外精炼设备真空系统的设计分析
Analysis and improvement measures for vacuum system in titanium powder plant;
钛白粉厂真空系统故障诊断及改进措施
Researches and Applications of the Waste Gas Treatment Plan for Vacuum Systems;
真空系统废气处理方案研究与应用
The analysis and treatment of PET vaccum system abnormal running;
聚酯真空系统异常分析及处理
The vaccum system composition of PET plant in Urumqi Petrochemical Company were introduced,including EG circulation,booster pump and EJ spray.
介绍了乌鲁木齐石化聚酯装置真空系统的组成,包括EG循环,增压泵,EJ喷淋等,影响整个真空系统效果的因素及聚酯装置失真空的处理方法。
The vaccum system composition and characteristics of Zimmer PET process production were introduced.
介绍了吉玛PET工艺生产真空系统的组成及特点,并结合生产实践,对真空系统常见问题进行了分析和总结。
During the process of steam turbine start-up and normal operation,vacuum extraction equipment must run,whether it works normally effects on the vacuum of condenser directly and decide whether turbo-generator can operate safely and economically.
汽轮发电机组在启动和正常运行过程中,抽真空设备都要投入运行,其工作的正常与否直接影响凝汽器的真空以及机组能否安全、经济运行。
Design Analysis of Vacuum System for Concentration Unit of Wet-process Phosphoric Acid
湿法磷酸浓缩装置真空系统设计分析
Key Technology and Design of Vacuum Tank Discharge in Vacuum Sewerage System
真空排水系统真空罐排放的关键技术与设计
Design of Automatic Control System for the Vacuum Degree of the Plastic Extrusion Machine Vacuum Sizing Device
真空定径装置真空度自动控制系统设计
DESIGN OF THE VACUUM SYSTEM FOR EXCISER LASER ABLATION DEPOSITION
准分子激光淀积装置真空系统的设计
Parametric Design and CAD System Development of Water Ring Vacuum Pump
水环真空泵参数化设计与CAD系统开发
The Design of Vacuum Dust Absorption System of Boiler Houses in the Thermal Power Plant
火电厂锅炉房真空负压吸尘系统设计
Design and Simulation of Control System of submarine-to-air Missile Capsule
潜空导弹运载器控制系统设计与仿真
Design of a Vacuum Freeze-Drying Control System Based on ARM+FPGA
基于ARM+FPGA的真空冻干控制系统设计
Design and Implementation of Ship Formation Air Defense Federation
舰艇编队防空仿真系统的设计与实现
Design on Simulation System of Air Defense Forces Group Operation Based on HLA
基于HLA的防空群作战仿真系统设计
Design and Implementation of Training Simulation System for Surface-to-Air Missile
地空导弹训练仿真系统的设计与实现
Design and Simulation of Guidance and Control System for Air-to-Air Missile;
空空导弹制导控制系统设计与仿真研究
Simulation system design of ground to air defense operation supported by spatial information
空间信息支持地面防空作战仿真系统设计
Study and Design of the Transformer Vacuum Dry Equipment Monitoring and Control System;
变压器真空干燥设备的监控系统研究与设计
Designing the Control System of the Small Double-Cauldron Vacuum Frying Equipment;
小型真空双锅油炸设备控制系统的设计
Design of Visual Simulation System of Space Tether-Robot On-Orbit Capture
空间绳系机器人在轨捕获视景仿真系统设计
Design of NC Motion System of Large Vacuum EBW Machine
大型真空电子束焊机数控运动系统的设计
Design of Orbit Debris Environment and Collision Alert System
空间碎片环境与碰撞预警仿真系统设计
